Skip to content
EduFacturing

Temperature and other towers: an STL and ready code for your slicer

Choose a tower type and values and get an STL model and code that changes one setting as the tower grows: temperature, retraction, speed, acceleration, flow or fan. For K-factor you get ready G-code lines. Then print it and see which block is cleanest.

Part of Pro, 15 EUR a month.

What a temperature tower and other calibration towers are

A temperature tower is a test model of several blocks, each printed at a different temperature; other calibration towers do the same with retraction, speed, flow or another setting. You see which block is cleanest and take its value. This temperature tower generator from EduFacturing, part of Pro, builds the tower and the code that changes the setting with height.

One tower gathers several values into one print, and the change of setting is built into the code instead of being written by hand.

The G-code file you drop in is processed in your browser and goes nowhere unless you save it to the library.

The AutoTowers welcome window: three steps (configure the tower, prepare the slicer, upload G-code directly) over the menu of tower types and the 3D preview
The AutoTowers welcome window: three steps (configure the tower, prepare the slicer, upload G-code directly) over the menu of tower types and the 3D preview

What the calibration tower generator does

Builds 9 test types and a combined one

Temperature, retraction (distance and speed), speed, acceleration, flow, cooling fan, auxiliary fan. Eight are towers; the ninth, K-factor, is printed lines. The combined one changes two settings.

Gives a model and code for your slicer

An STL or 3MF; a .py script for Cura; code for PrusaSlicer and OrcaSlicer that goes into Before layer change; a TUNING_TOWER command for Klipper.

Inserts the changes into a finished G-code

Drop in a sliced .gcode file and get the same file with the setting changes at the right layers.

Works out the value from a block

Enter the number of the cleanest block and get the value and where to set it in your slicer.

When you need a temperature tower or another tower

You print a calibration tower when a setting should be chosen by result, not copied from someone else's profile.

  • A new filament

    A temperature tower: you look for the block where bridges and overhangs are clean.

  • Strings between parts

    A retraction tower with a growing retraction distance or speed.

  • Ripples on the walls

    Speed and acceleration on a smooth cylinder for VFA instead of a square tower.

  • Pressure Advance

    Lines with a growing K-factor (Linear Advance in Marlin) for Marlin or Klipper.

How the value of each block is worked out

A tower is several blocks of 10 mm each by default. With a step width above 0, every block gets one value; with 0, which is the setting when the app opens, the value grows smoothly with height.

  1. Start and step

    You set a start value and a step. By default the temperature tower has 5 blocks: 220, 215, 210, 205 and 200 °C. The step can also be negative.

  2. Where the setting changes

    The blocks start above the base (2 mm by default). The first value applies from layer 0. The step width is 0 when the app opens: then the code for PrusaSlicer and OrcaSlicer, the Klipper command and the insert into a finished G-code change the value smoothly with height. The Cura script and the 3MF always change it per block.

  3. Commands by firmware

    Marlin and Klipper get different commands, for example M207 and SET_RETRACTION for retraction, M104 or M109 for temperature. You pick Marlin, Klipper or both.

The sums in the app
Applies toFormulaMeaning
Value of a blockv = start + (block − 1) · stepblock 1 is the bottom one; it holds with a step width above 0, for Cura and for the 3MF
Layer where a block startslayer = base / layer + (block − 1) · block / layerall three heights are in mm; at 2, 10 and 0.2 mm block 1 starts on layer 10 and block 2 on layer 60
Smooth mode (width 0)v = start + (z − base) / block · stepz is the layer height in mm
FanS = % · 2.55the percentage is limited between 0 and 100 and becomes a number from 0 to 255 for M106

Nine test types and ready code for your slicer

  • Nine types in one tool

    Temperature, retraction (distance and speed), speed, acceleration, flow, two fans and K-factor, plus a combined test.

  • Code for Marlin and for Klipper

    Commands are written for the firmware you pick, and Klipper also gets a ready TUNING_TOWER command.

  • Works on a sliced G-code

    It recognises the layers in G-code from Cura, PrusaSlicer and OrcaSlicer.

What AutoTowers does not do

AutoTowers does not print or slice: you slice the tower yourself. The 3MF is for PrusaSlicer and is a simplified block without the overhangs and numbers of the STL.

You read the result from the print: the app cannot see the tower. Commands work only if the firmware supports them; for retraction Marlin needs firmware retraction switched on.

The K-factor lines are a ready G-code with a 60 °C bed, a 0.4 mm nozzle and 0.2 mm layers, and they do not go through the slicer.

Questions about the temperature tower and calibration towers

What is a temperature tower?

A print of blocks stacked on top of each other, each at a different nozzle temperature. You see which block came out cleanest and take its temperature.

How to read a temperature tower?

Look at bridges, overhangs and strings on each block. Enter the number of the cleanest block, and the app works out the temperature and tells you where to set it.

How to print a temperature tower?

Set the start temperature and step, download the STL and the code for your slicer, slice with the same layer height and print. The code changes the nozzle temperature as the tower grows.

How to calibrate retraction?

Print a retraction tower: the distance grows by 0.5 mm per block, starting from 1 mm by default. Take the value of the block with the fewest strings.

Which slicers are supported?

Cura through a script, PrusaSlicer and OrcaSlicer through code for Before layer change. Every slicer takes the STL, and Klipper gets a TUNING_TOWER command.

How much does the temperature tower generator cost?

It is part of Pro for 15 EUR a month. Pro also opens the other Pro tools.

The calibration tower generator is part of Pro

Pro costs 15 EUR a month and opens all 45 Pro tools.

Make a tower for your printer

Part of Pro, 15 EUR a month.