Skip to content Skip to content
EduFacturing
Printers

DF2 – Specs and Settings

DF2 – Specs and Settings

The Raise3D DF2 is a prosumer-class desktop DLP printer designed for engineering, dental and jewellery applications where FDM accuracy falls short. Raise3D's closed ecosystem (printer, resins and software) delivers predictable, repeatable results at a production level.

What it is

The DF2 uses Digital Light Processing (DLP): a technology in which a UV projector exposes an entire layer at once rather than scanning point by point. The result is high isotropic accuracy, smooth surfaces and short layer times regardless of geometry complexity. Raise3D positions the DF2 within a closed material system: the machine, resins and the ideaMaker slicer are jointly optimised, shifting quality responsibility from the user to the manufacturer. The target audience is small engineering bureaux, dental laboratories and jewellery ateliers producing short runs with repeatable tolerances.

Technical specifications

TechnologyDLP (Digital Light Processing, UV projector)
Build volume192 × 108 × 245 mm
XY resolution75 µm (2560 × 1440 pixels)
Layer thickness25 – 100 µm
Light source405 nm UV DLP projector
Material systemClosed: Raise3D resins (Engineering, Dental, Castable, Clear, Flexible)
SlicerideaMaker (Raise3D, built-in profile per resin)
Class / PriceProsumer · ~€3 500

Applications and industries

  • Engineering prototypes and short runs (accurate functional prototypes and end-use parts with tolerances under 0.1 mm) ideal for fit-checks and aerodynamic shapes (Industrial design, Aerospace, Automotive)
  • Dental models and surgical guides: biocompatible dental models, occlusal splints and surgical guides with clinical accuracy using certified resins (Dentistry, Medical devices)
  • Jewellery, castables and micro-details: wax-like castable resins for direct investment casting, jewellery masters with fine textures and ornaments (Jewellery, Artistic casting)

Production workflow

  1. Check the platform level with the built-in wizard before each session. Even first-layer thickness: prevents model detachment from the build plate.
  2. Gently shake the resin tank and avoid direct sunlight when loading resin. Homogeneous mixture without sediment: ensures uniform exposure on every layer.
  3. Load the resin's preset profile in ideaMaker and do not override exposure time manually. Optimised bond strength and edge accuracy as validated by Raise3D.
  4. After printing, wash the model in IPA (or Raise3D Wash) for 5–10 min, then post-cure 10–15 min in a UV chamber at 60°C. Full resin polymerisation: final mechanical and chemical properties are achieved.

Key considerations

Closed ecosystem (limited resin choice) the DF2 is optimised for Raise3D resins; third-party resins are not officially supported and require manual exposure parameter calibrationUse exclusively Raise3D validated resins for production results; if using a third-party resin, run an exposure optimisation test matrix.
Insufficient post-curing (models straight off the build plate are only partially polymerised) brittle, tacky and with lower chemical resistanceA full wash + UV post-cure cycle at the temperature and time Raise3D recommends for the specific resin is mandatory.
Delamination / release failure from FEP film, with large solid cross-sections or a worn FEP film the model fails to release cleanly from the tank bottom and warps or collapsesAdd supports (tilt angle ≥ 45°), break up solid cross-sections with drain holes, replace the FEP film every ~2 litres of resin.
Dimensional deviation from anisotropic shrinkage: different resins shrink 0.5–2% during UV polymerisation; without compensation bores and fits miss nominal sizeUse the resin-specific scaling compensation factor in ideaMaker; validate with a test coupon for critical fits.

Materials and applications

Pick a material/alloy this machine processes to see its properties and typical applications:

↑ Pick a material
Properties
Applications

Conclusion

The Raise3D DF2 is a machine for those who value accuracy over speed. The closed ecosystem shifts parameter responsibility away from the user: simply load a pre-validated profile and get a predictable result. For engineering bureaux, dental laboratories and jewellery ateliers where tolerance and repeatability carry direct production significance, the DF2 delivers industrial accuracy at a desktop price.

The full picture

This article is one page from The Big Book of 3D Printing: 704 illustrated pages covering every technology, material and fix in one reference.

Read it on Kindle →

Engineer, author of The Big Book of 3D Printing and additive manufacturing expert

We use cookies. Essential ones make the site work.

Want Google's AI to give you accurate 3D-printing answers? Add EduFacturing as a Preferred Source (opens Google, add “edufacturing.com”).